# Technical Entity Reference # Technical Entity Reference Complete reference of all Home Assistant entities for EP1 and EPL, including default values and valid ranges. --- # Everything Presence One (EP1) - SEN0609 ## Binary Sensors | Entity | Description | Default | |--------|-------------|---------| | mmWave | Presence detected by mmWave sensor | \- | | PIR | Motion detected by PIR sensor | \- | | Occupancy | Combined PIR + mmWave (either triggers on) | \- | ## Sensors | Entity | Unit | Description | |--------|------|-------------| | Temperature | °C | Room temperature | | Humidity | % | Relative humidity | | Illuminance | lx | Ambient light level | | mmWave Target Distance\* | m | Distance to detected target | | mmWave Target Speed\* | m/s | Speed of detected target | | mmWave Target Energy\* | \- | Signal strength of detection | | mmWave Target Count\* | \- | Number of targets detected | \*Disabled by default. Enable in entity settings. ## Configuration Numbers | Entity | Range | Default | Step | Description | |--------|-------|---------|------|-------------| | mmWave Minimum Distance | 0\.6-25 m | 0\.6 | 0\.1 | Ignore targets closer than this | | mmWave Max Distance | 0-25 m | 12 | 0\.1 | Ignore targets farther than this | | mmWave Trigger Distance | 0-25 m | 6 | 0\.1 | Distance threshold for initial trigger | | mmWave Sustain Sensitivity | 0-9 | 7 | 1 | Sensitivity after initial detection | | mmWave Trigger Sensitivity | 0-9 | 5 | 1 | Sensitivity for initial detection | | mmWave On Latency | 0-2 s | 0 | 0\.25 | Delay before reporting presence | | mmWave Off Latency | 1-600 s | 15 | 5 | Delay before clearing presence | | Temperature Offset | \-10 to 10 °C | 0 | 0\.1 | Calibration offset | | Humidity Offset | \-20 to 20 % | 0 | 1 | Calibration offset | | Illuminance Offset | \-100 to 100 lx | 0 | 5 | Calibration offset | | mmWave Threshold Factor\* | 1-20 | 5 | 1 | Detection threshold (Distance mode) | ## Configuration Selects | Entity | Options | Default | Description | |--------|---------|---------|-------------| | mmWave Mode\* | Presence Detection, Distance and Speed | Presence Detection | Operating mode | | Distance/Speed Update Rate\* | 0\.3s, 0.4s, 0.5s | 0\.5s | How often distance values update | ## Switches | Entity | Default | Description | |--------|---------|-------------| | mmWave sensor\* | On | Start/stop mmWave sensor | | UART presence output\* | Off | Enable UART presence data | | UART target output\* | Off | Enable UART target data | | Micro-motion Detection\* | Off | Detect very small movements | ## Buttons | Entity | Description | |--------|-------------| | Set Distance | Apply distance settings to sensor | | Set Sensitivity | Apply sensitivity settings to sensor | | ESP Reboot | Restart the device | | Factory Reset mmWave\* | Reset mmWave to factory defaults | ## Lights | Entity | Description | |--------|-------------| | mmWave LED | Toggle mmWave sensor LED | | ESP32 LED | Toggle ESP32 status LED | --- # Everything Presence Lite (EPL) - LD2450 ## Binary Sensors | Entity | Description | |--------|-------------| | Occupancy | Overall room presence | | Zone 1-4 Occupancy | Presence in specific zone | | Target 1-3 Active | Whether each target slot is active | | Assumed Present | Assume present mode is active | ## Sensors | Entity | Unit | Description | |--------|------|-------------| | Illuminance | lx | Ambient light level | | Zone 1-4 Target Count | \- | Targets in each zone | | Occupancy Mask 1-2 Target Count | \- | Targets in exclusion areas | | Target 1-3 X | mm | Horizontal position | | Target 1-3 Y | mm | Distance from sensor | | Target 1-3 Distance | mm | Direct distance | | Target 1-3 Angle | ° | Angle from center | | Target 1-3 Speed | mm/s | Movement speed | | Target 1-3 Resolution | mm | Detection resolution | | Assumed Present Remaining | s | Countdown for assumed presence | ## Configuration Numbers | Entity | Range | Default | Step | Description | |--------|-------|---------|------|-------------| | Occupancy Off Delay | 0-600 s | 15 | 1 | Delay before clearing occupancy | | Max Distance | 0-600 cm | 600 | 1 | Maximum detection range | | Installation Angle | \-45 to 45 ° | 0 | 1 | Virtual orientation adjustment | | Illuminance Offset | \-100 to 100 lx | 0 | 5 | Calibration offset | | Assume Present Timeout | 0-600 s | 15 | 1 | Duration to assume presence | | Exit Threshold Pct | 0-100 % | 10 | 1 | Exit detection sensitivity | | Zone 1-4 Begin/End X | \-6000 to 6000 mm | 0 | 10 | Zone horizontal bounds | | Zone 1-4 Begin/End Y | 0-6000 mm | 0 | 10 | Zone distance bounds | | Zone 1-4 Off Delay | 0-600 s | 0 | 1 | Per-zone off delay | | Occupancy Mask 1-2 Begin/End X/Y | varies | 0 | 10 | Exclusion zone bounds | | Entry Zone 1-2 Begin/End X/Y | varies | 0 | 10 | Entry zone bounds | | Stale Target Timeout | 0-600 s | 30 | 1 | Clear stuck targets after | ## Configuration Selects | Entity | Options | Default | Description | |--------|---------|---------|-------------| | Tracking Behaviour | None, Targets Position, +Zone Count, +Targets Active, +Distance/Angle, +Speed/Resolution | \+Speed/Resolution | Which sensors to report | | Update Speed | 0\.1s, 0.2s, 0.3s, 0.5s, 1s | 0\.3s | Reporting frequency | | Extra Entities Update | Every update, 2nd, 3rd, 5th, 10th | Every update | Update frequency for extras | ## Switches | Entity | Default | Description | |--------|---------|-------------| | Stale Target Reset | Off | Enable automatic target clearing | | Inverse Mounting | Off | Flip for upside-down installation | | Entry Exit Enabled | Off | Enable entry/exit zone detection | | Polygon Zones | Off | Enable polygon zone mode | | mmWave Bluetooth\* | Off | Enable LD2450 Bluetooth | ## Buttons | Entity | Description | |--------|-------------| | ESP Reboot | Restart the device | | Factory Reset mmWave\* | Reset mmWave to factory defaults | ## Lights | Entity | Description | |--------|-------------| | ESP32 LED | Toggle ESP32 status LED | --- ## Notes * Entities marked with \* are disabled by default. Enable via "Show disabled entities" in Home Assistant. * Zone coordinates use millimeters. X is left/right (-/+), Y is distance from sensor. * Press "Set Distance" or "Set Sensitivity" buttons after changing EP1 settings. * Use the Everything Presence Zone Configurator for visual zone setup (EPL). --- **Documents** - [EP1 vs EPL: Which Sensor is Right for You?](https://docs.everythingsmart.io/s/products/doc/ep1-vs-epl-which-sensor-is-right-for-you-5B3RxiY3Kp) - [Everything Presence One (EP1)](https://docs.everythingsmart.io/s/products/doc/everything-presence-one-ep1-3R178yZSUP) - [Everything Presence Pro](https://docs.everythingsmart.io/s/products/doc/everything-presence-pro-nh3fIXmow9) - [Everything Presence Lite (EPL)](https://docs.everythingsmart.io/s/products/doc/everything-presence-lite-epl-ZVnBzYzuX2) - [Zone Configurator](https://docs.everythingsmart.io/s/products/doc/zone-configurator-93b9scGsa2) - [Knowledge Base Articles](https://docs.everythingsmart.io/s/products/doc/knowledge-base-articles-KnRRmk4zvt)