mmWave

Presence detected by mmWave sensor

-

PIR

Motion detected by PIR sensor

-

Occupancy

Combined PIR + mmWave (either triggers on)

-

Temperature

°C

Room temperature

Humidity

%

Relative humidity

Illuminance

lx

Ambient light level

mmWave Target Distance*

m

Distance to detected target

mmWave Target Speed*

m/s

Speed of detected target

mmWave Target Energy*

-

Signal strength of detection

mmWave Target Count*

-

Number of targets detected

mmWave Minimum Distance

0.6-25 m

0.6

0.1

Ignore targets closer than this

mmWave Max Distance

0-25 m

12

0.1

Ignore targets farther than this

mmWave Trigger Distance

0-25 m

6

0.1

Distance threshold for initial trigger

mmWave Sustain Sensitivity

0-9

7

1

Sensitivity after initial detection

mmWave Trigger Sensitivity

0-9

5

1

Sensitivity for initial detection

mmWave On Latency

0-2 s

0

0.25

Delay before reporting presence

mmWave Off Latency

1-600 s

15

5

Delay before clearing presence

Temperature Offset

-10 to 10 °C

0

0.1

Calibration offset

Humidity Offset

-20 to 20 %

0

1

Calibration offset

Illuminance Offset

-100 to 100 lx

0

5

Calibration offset

mmWave Threshold Factor*

1-20

5

1

Detection threshold (Distance mode)

mmWave Mode*

Presence Detection, Distance and Speed

Presence Detection

Operating mode

Distance/Speed Update Rate*

0.3s, 0.4s, 0.5s

0.5s

How often distance values update

mmWave sensor*

On

Start/stop mmWave sensor

UART presence output*

Off

Enable UART presence data

UART target output*

Off

Enable UART target data

Micro-motion Detection*

Off

Detect very small movements

Set Distance

Apply distance settings to sensor

Set Sensitivity

Apply sensitivity settings to sensor

ESP Reboot

Restart the device

Factory Reset mmWave*

Reset mmWave to factory defaults

mmWave LED

Toggle mmWave sensor LED

ESP32 LED

Toggle ESP32 status LED

Occupancy

Overall room presence

Zone 1-4 Occupancy

Presence in specific zone

Target 1-3 Active

Whether each target slot is active

Assumed Present

Assume present mode is active

Illuminance

lx

Ambient light level

Zone 1-4 Target Count

-

Targets in each zone

Occupancy Mask 1-2 Target Count

-

Targets in exclusion areas

Target 1-3 X

mm

Horizontal position

Target 1-3 Y

mm

Distance from sensor

Target 1-3 Distance

mm

Direct distance

Target 1-3 Angle

°

Angle from center

Target 1-3 Speed

mm/s

Movement speed

Target 1-3 Resolution

mm

Detection resolution

Assumed Present Remaining

s

Countdown for assumed presence

Occupancy Off Delay

0-600 s

15

1

Delay before clearing occupancy

Max Distance

0-600 cm

600

1

Maximum detection range

Installation Angle

-45 to 45 °

0

1

Virtual orientation adjustment

Illuminance Offset

-100 to 100 lx

0

5

Calibration offset

Assume Present Timeout

0-600 s

15

1

Duration to assume presence

Exit Threshold Pct

0-100 %

10

1

Exit detection sensitivity

Zone 1-4 Begin/End X

-6000 to 6000 mm

0

10

Zone horizontal bounds

Zone 1-4 Begin/End Y

0-6000 mm

0

10

Zone distance bounds

Zone 1-4 Off Delay

0-600 s

0

1

Per-zone off delay

Occupancy Mask 1-2 Begin/End X/Y

varies

0

10

Exclusion zone bounds

Entry Zone 1-2 Begin/End X/Y

varies

0

10

Entry zone bounds

Stale Target Timeout

0-600 s

30

1

Clear stuck targets after

Tracking Behaviour

None, Targets Position, +Zone Count, +Targets Active, +Distance/Angle, +Speed/Resolution

+Speed/Resolution

Which sensors to report

Update Speed

0.1s, 0.2s, 0.3s, 0.5s, 1s

0.3s

Reporting frequency

Extra Entities Update

Every update, 2nd, 3rd, 5th, 10th

Every update

Update frequency for extras

Stale Target Reset

Off

Enable automatic target clearing

Inverse Mounting

Off

Flip for upside-down installation

Entry Exit Enabled

Off

Enable entry/exit zone detection

Polygon Zones

Off

Enable polygon zone mode

mmWave Bluetooth*

Off

Enable LD2450 Bluetooth

ESP Reboot

Restart the device

Factory Reset mmWave*

Reset mmWave to factory defaults

ESP32 LED

Toggle ESP32 status LED