Technical Entity Reference
Look up Everything Presence sensor entities and controls to understand their purpose when configuring your smart home.
Complete reference of all Home Assistant entities for EP1 and EPL, including default values and valid ranges.
Everything Presence One (EP1) - SEN0609
Binary Sensors
| Entity | Description | Default |
|---|---|---|
| mmWave | Presence detected by mmWave sensor | - |
| PIR | Motion detected by PIR sensor | - |
| Occupancy | Combined PIR + mmWave (either triggers on) | - |
Sensors
| Entity | Unit | Description |
|---|---|---|
| Temperature | °C | Room temperature |
| Humidity | % | Relative humidity |
| Illuminance | lx | Ambient light level |
| mmWave Target Distance* | m | Distance to detected target |
| mmWave Target Speed* | m/s | Speed of detected target |
| mmWave Target Energy* | - | Signal strength of detection |
| mmWave Target Count* | - | Number of targets detected |
*Disabled by default. Enable in entity settings.
Configuration Numbers
| Entity | Range | Default | Step | Description |
|---|---|---|---|---|
| mmWave Minimum Distance | 0.6-25 m | 0.6 | 0.1 | Ignore targets closer than this |
| mmWave Max Distance | 0-25 m | 12 | 0.1 | Ignore targets farther than this |
| mmWave Trigger Distance | 0-25 m | 6 | 0.1 | Distance threshold for initial trigger |
| mmWave Sustain Sensitivity | 0-9 | 7 | 1 | Sensitivity after initial detection |
| mmWave Trigger Sensitivity | 0-9 | 5 | 1 | Sensitivity for initial detection |
| mmWave On Latency | 0-2 s | 0 | 0.25 | Delay before reporting presence |
| mmWave Off Latency | 1-600 s | 15 | 5 | Delay before clearing presence |
| Temperature Offset | -10 to 10 °C | 0 | 0.1 | Calibration offset |
| Humidity Offset | -20 to 20 % | 0 | 1 | Calibration offset |
| Illuminance Offset | -100 to 100 lx | 0 | 5 | Calibration offset |
| mmWave Threshold Factor* | 1-20 | 5 | 1 | Detection threshold (Distance mode) |
Configuration Selects
| Entity | Options | Default | Description |
|---|---|---|---|
| mmWave Mode* | Presence Detection, Distance and Speed | Presence Detection | Operating mode |
| Distance/Speed Update Rate* | 0.3s, 0.4s, 0.5s | 0.5s | How often distance values update |
Switches
| Entity | Default | Description |
|---|---|---|
| mmWave sensor* | On | Start/stop mmWave sensor |
| UART presence output* | Off | Enable UART presence data |
| UART target output* | Off | Enable UART target data |
| Micro-motion Detection* | Off | Detect very small movements |
Buttons
| Entity | Description |
|---|---|
| Set Distance | Apply distance settings to sensor |
| Set Sensitivity | Apply sensitivity settings to sensor |
| ESP Reboot | Restart the device |
| Factory Reset mmWave* | Reset mmWave to factory defaults |
Lights
| Entity | Description |
|---|---|
| mmWave LED | Toggle mmWave sensor LED |
| ESP32 LED | Toggle ESP32 status LED |
Everything Presence Lite (EPL) - LD2450
Binary Sensors
| Entity | Description |
|---|---|
| Occupancy | Overall room presence |
| Zone 1-4 Occupancy | Presence in specific zone |
| Target 1-3 Active | Whether each target slot is active |
| Assumed Present | Assume present mode is active |
Sensors
| Entity | Unit | Description |
|---|---|---|
| Illuminance | lx | Ambient light level |
| Zone 1-4 Target Count | - | Targets in each zone |
| Occupancy Mask 1-2 Target Count | - | Targets in exclusion areas |
| Target 1-3 X | mm | Horizontal position |
| Target 1-3 Y | mm | Distance from sensor |
| Target 1-3 Distance | mm | Direct distance |
| Target 1-3 Angle | ° | Angle from center |
| Target 1-3 Speed | mm/s | Movement speed |
| Target 1-3 Resolution | mm | Detection resolution |
| Assumed Present Remaining | s | Countdown for assumed presence |
Configuration Numbers
| Entity | Range | Default | Step | Description |
|---|---|---|---|---|
| Occupancy Off Delay | 0-600 s | 15 | 1 | Delay before clearing occupancy |
| Max Distance | 0-600 cm | 600 | 1 | Maximum detection range |
| Installation Angle | -45 to 45 ° | 0 | 1 | Virtual orientation adjustment |
| Illuminance Offset | -100 to 100 lx | 0 | 5 | Calibration offset |
| Assume Present Timeout | 0-600 s | 15 | 1 | Duration to assume presence |
| Exit Threshold Pct | 0-100 % | 10 | 1 | Exit detection sensitivity |
| Zone 1-4 Begin/End X | -6000 to 6000 mm | 0 | 10 | Zone horizontal bounds |
| Zone 1-4 Begin/End Y | 0-6000 mm | 0 | 10 | Zone distance bounds |
| Zone 1-4 Off Delay | 0-600 s | 0 | 1 | Per-zone off delay |
| Occupancy Mask 1-2 Begin/End X/Y | varies | 0 | 10 | Exclusion zone bounds |
| Entry Zone 1-2 Begin/End X/Y | varies | 0 | 10 | Entry zone bounds |
| Stale Target Timeout | 0-600 s | 30 | 1 | Clear stuck targets after |
Configuration Selects
| Entity | Options | Default | Description |
|---|---|---|---|
| Tracking Behaviour | None, Targets Position, +Zone Count, +Targets Active, +Distance/Angle, +Speed/Resolution | +Speed/Resolution | Which sensors to report |
| Update Speed | 0.1s, 0.2s, 0.3s, 0.5s, 1s | 0.3s | Reporting frequency |
| Extra Entities Update | Every update, 2nd, 3rd, 5th, 10th | Every update | Update frequency for extras |
Switches
| Entity | Default | Description |
|---|---|---|
| Stale Target Reset | Off | Enable automatic target clearing |
| Inverse Mounting | Off | Flip for upside-down installation |
| Entry Exit Enabled | Off | Enable entry/exit zone detection |
| Polygon Zones | Off | Enable polygon zone mode |
| mmWave Bluetooth* | Off | Enable LD2450 Bluetooth |
Buttons
| Entity | Description |
|---|---|
| ESP Reboot | Restart the device |
| Factory Reset mmWave* | Reset mmWave to factory defaults |
Lights
| Entity | Description |
|---|---|
| ESP32 LED | Toggle ESP32 status LED |
Notes
- Entities marked with * are disabled by default. Enable via "Show disabled entities" in Home Assistant.
- Zone coordinates use millimeters. X is left/right (-/+), Y is distance from sensor.
- Press "Set Distance" or "Set Sensitivity" buttons after changing EP1 settings.
- Use the Everything Presence Zone Configurator for visual zone setup (EPL).