Everything Presence Lite — Homey Sensors and Controls
Understand the sensors and controls available for Everything Presence Lite in Homey and how to use them in your setup.
Common device capabilities exposed to Homey for Everything Presence Lite.
| Capability | Type | What it shows |
|---|---|---|
| alarm_motion | Alarm | Motion/presence state from the device. |
| onoff.esp32_led | Switch | Turn the board status LED on/off. |
| measure_luminance | Sensor | Light level (lux). |
| alarm_generic.zone1_occupancy | Alarm | Zone 1 occupancy (on when a target is inside Zone 1). |
| alarm_generic.zone2_occupancy | Alarm | Zone 2 occupancy. |
| alarm_generic.zone3_occupancy | Alarm | Zone 3 occupancy. |
| alarm_generic.zone4_occupancy | Alarm | Zone 4 occupancy. |
| measure_x.target1 | Sensor | Target 1 X position in millimetres (mm). |
| measure_y.target1 | Sensor | Target 1 Y position in millimetres (mm). |
| measure_distance.target1 | Sensor | Target 1 distance in millimetres (mm). |
| measure_angle.target1 | Sensor | Target 1 angle in degrees. |
| measure_speed.target1 | Sensor | Target 1 speed in mm/s. |
| measure_x.target2 | Sensor | Target 2 X position in millimetres (mm). |
| measure_y.target2 | Sensor | Target 2 Y position in millimetres (mm). |
| measure_distance.target2 | Sensor | Target 2 distance in millimetres (mm). |
| measure_angle.target2 | Sensor | Target 2 angle in degrees. |
| measure_speed.target2 | Sensor | Target 2 speed in mm/s. |
| measure_x.target3 | Sensor | Target 3 X position in millimetres (mm). |
| measure_y.target3 | Sensor | Target 3 Y position in millimetres (mm). |
| measure_distance.target3 | Sensor | Target 3 distance in millimetres (mm). |
| measure_angle.target3 | Sensor | Target 3 angle in degrees. |
| measure_speed.target3 | Sensor | Target 3 speed in mm/s. |
Tip
- Zone occupancy depends on zones being configured on the device. Configure zones in Homey: open the EPL device > Settings > Zone 1-4 (set Begin/End X and Y in mm, and Off Delay as needed).
- Target positions (X/Y) and distance/angle/speed are optional advanced signals for custom Flows.
Zones and masks tips
- Coordinates and units (when looking at the device)
- X: left (−) to right (+), Y: near (−) to far (+); values in millimetres (mm).
- Start with a conservative rectangle, test, then expand.
- Overlap and order
- Avoid overlapping zones to keep automations unambiguous.
- Masks hide areas from occupancy; define masks first, then tune zones.
- Off delays
- Use per‑zone Off Delay to keep a zone occupied briefly after movement stops.
- Enable additional zones
- Zones 2–4 are available in Settings; set Begin/End X/Y and Off Delay for each.

Advanced settings (device settings)
These controls appear under the EPL device → Settings in Homey.
| Setting (label) | ID | Units | What it does |
|---|---|---|---|
| Occupancy Off Delay (s) | epl_off_delay | s | How long Occupancy stays on after no motion. |
| Maximum Detection Distance (cm) | epl_distance | cm | Maximum detection range for presence. |
| Installation Angle (deg) | epl_installation_angle | deg | Adjusts the sensor’s orientation virtually to match how it’s mounted. |
| Illuminance Offset (lx) | illuminance_offset | lx | Fine-tune reported light level. |
| Zone 1 Begin/End X (mm) | zone1_begin_x / zone1_end_x | mm | Left/right edges of Zone 1. |
| Zone 1 Begin/End Y (mm) | zone1_begin_y / zone1_end_y | mm | Near/far edges of Zone 1. |
| Zone 1 Off Delay (s) | epl_zone1_off_delay | s | How long Zone 1 stays on after no targets. |
| Zone 2 Begin/End X (mm) | zone2_begin_x / zone2_end_x | mm | Left/right edges of Zone 2. |
| Zone 2 Begin/End Y (mm) | zone2_begin_y / zone2_end_y | mm | Near/far edges of Zone 2. |
| Zone 2 Off Delay (s) | epl_zone2_off_delay | s | How long Zone 2 stays on after no targets. |
| Zone 3 Begin/End X (mm) | zone3_begin_x / zone3_end_x | mm | Left/right edges of Zone 3. |
| Zone 3 Begin/End Y (mm) | zone3_begin_y / zone3_end_y | mm | Near/far edges of Zone 3. |
| Zone 3 Off Delay (s) | epl_zone3_off_delay | s | How long Zone 3 stays on after no targets. |
| Zone 4 Begin/End X (mm) | zone4_begin_x / zone4_end_x | mm | Left/right edges of Zone 4. |
| Zone 4 Begin/End Y (mm) | zone4_begin_y / zone4_end_y | mm | Near/far edges of Zone 4. |
| Zone 4 Off Delay (s) | epl_zone4_off_delay | s | How long Zone 4 stays on after no targets. |
| Mask 1 Begin/End X/Y (mm) | occupancy_mask_1_begin_x / _end_x / _begin_y / _end_y | mm | Area to ignore for occupancy (mask 1). |
| Mask 2 Begin/End X/Y (mm) | occupancy_mask_2_begin_x / _end_x / _begin_y / _end_y | mm | Area to ignore for occupancy (mask 2). |
| Stale Target Reset Timeout (s) | stale_target_reset_timeout | s | Time before a “stuck” target is cleared. |
| Inverse Mounting (Upside-down) | inverse_mounting | On/Off | Flip orientation if installed upside down. |
| Aggressive Target Clearing | stale_target_reset | On/Off | Enable faster clearing of stuck targets. |
| mmWave Bluetooth | bluetooth_switch | On/Off | Toggle mmWave Bluetooth (for maintenance). |